Wednesday, November 26, 2014

Remove and Replace of the Appliance and Other Stuff

Oy!  Yesterday was a day!  A day and a half kind of day.  As you recall, the over the range microwave/convection oven finally died and stayed dead.  If we so much as plugged it in, it flipped the breaker, immediately.  We ordered a new one from Home Depot (free shipping).  Yesterday we took the bus and the appliance to Premier Motorcoach Services. After our last experience with them, we swore hell would freeze over before we went back.  Our issue with them was shop loading.  We had about 3 days of work which took them eight days.  They would request the RV to be on site at 8:30, and at 11:00 we would drive by and see it hadn't been moved into the shop.  Over all, the work was OK, but their inefficiency totally soured us on them.  However, we knew that they could install the appliance as they had done so before.
After the broken appliance was removed, it was discovered that the back of a cabinet over the microwave prevented the use of the nut set.  That's the silver circle at the back of the microwave. So they drilled through the bottom of the cabinet with a self tapping screw. That's not the way it should have been done.  Erik, the owner, was fairly upset with this.


The back of the cabinet had to be removed but was not going easily.  Here they are using a circular saw to try to make a portal to see how the wood was attached.


Now they are using a small reciprocating saw to try to remove the back of the cabinet.


That's part of the slide behind the cabinet back.  That wood piece is 1/2 inch plywood that was stapled every half inch all the way around.  Thus insuring that it would be difficult to remove, and that no present or future microwaves could be properly installed.  What the heck was Beaver thinking?


We had to take a little time out to go appreciate some nature.  We spent the day in the bus, so our presence would be a reminder that we're full timers, and this task really needed to be completed in one day.  I think if you're not around, it's easy to push your work to the back of the line.  It is, however, incredibly stressful watching them brute force part of your home out.


Eventually holes for the nut set were drilled in the proper place (for the first time in the life of the bus), the proper mounting brackets were used and the thing was installed.  It weighs 72 pounds and was just a bear to get in there.


The bottom set of screws were also a bear. 


There has been a total sea change at Premier.  Everyone there is new, except for the owners.  I'm more favorably inclined towards them these days.  I will say they do one of the best TV installs I've ever seen. 

To make things even better, the ice maker froze up (see what I did there?) while we were at Premier.  Upon arriving at home, we had to defrost the freezer, including the ice bergs that were stuck in the icemaker.
And then, and then, the breaker for the circuit that runs the laptops, phone chargers, wifi modem, TV, satellite receiver and satellite antenna started flipping. If there is anything that pushes me over the edge, it is random electronic weirdness because I'm helpless in the face of electronics that aren't working.  Using the random permutation theory of debugging, we removed the easiest component to change out - the power strip.  We've had it forever, and perhaps it was the problem.  So far the breaker is not popping, so one hopes we have solved the problem.

So that was our day in the glamorous lifestyle that is full time RVing in a Class A.

3 comments:

  1. Fingers crossed your multitude of issues is solved (please, power strip, be the thing!) Glamorous indeed! :-)

    ReplyDelete
  2. Yes, you had a bad day, but it beats sitting in the ER. Be thankful for the little things;-)

    ReplyDelete
  3. Glad things worked out for you. Sorry to hear about your previous experience with Premier. We had such a wonderful work done there that we are returning this year to have other things done.

    ReplyDelete